Alfain Svarog 320 HD PULSE Modular PL MIG/MAG welding machine

Welding synergy inverter MIG/MAG and MMA, pulse and full aluminum welding capability. Variants description: BL version with extendable Box module and large chassis with one gas cylinder holder (ready for installation of E.466 additional cooling module set) BS version with extendable Box module and Small chassis without gas cylinder holder (ready for A .466 additional cooling module set installation) WL version with water cooling module and large chassis with one gas cylinder holder WS version with water cooling module and small chassis without gas cylinder holder

You do not need to immediately spend money to buy a machine with liquid cooling of the burner. A big advantage of the SVAROG 320 HD PULSE modular module concept is the ability to supplement the machine with liquid cooling at any time and without the need for a specialized workshop. You can easily connect using basic tools and prepared connection material (included in the included cooling kit). The source comes standard with a control connector that you just plug in.

Economy and sustainability!

Inverter technology ensures low power consumption at a constant output power and thus reduces electricity consumption.

Efficiency 89%

According to standardized measurement methods, Svarog achieves 89% efficiency. This means that a large part of the power fed into the grid is converted into arc energy without loss.

Cooling

Coolant ACL-10 provides excellent sustainability due to its composition and extends the life of the system.

Filter!

In the basic equipment, a filter is placed in the cooling circuit, which captures all impurities. It protects the entire cooling system and the welding torch, is easy to inspect and can be cleaned repeatedly.

Easy setup WORKS!

Direct storage of 6 JOBS by long-pressing the button and direct recall of JOBS by short-pressing the button. We reserved a separate button for each JOB from 6. Calibration of the welding circuit The welding properties of the synergistic curve depend on many factors, such as the length of the welding torch, the length of the grounding cable, the quality of the grounding. , welding distance from grounding point, etc. Therefore, it is recommended to calibrate the welding circuit for the current welding conditions. The welding chain calibration function will prevent these effects.

Setting the EASY PULSE mode!

With just one push of a button, everything is set to pulse welding mode...

70% less finishing work!

Thanks to the impulse function, it is possible to avoid a difficult-to-control transition arc that is loaded with a large amount of splash.

Less welding spatter reduces finishing work by up to 70%.

A large selection of synergistic programs!

Steel SG/Fe, Cr/Ni, AlSi, AlMg, wire diameters 0.8; 1.0; 1.2 mm various gas mixtures

Lighting of the interior of the wire feeder.

A powerful LED effectively illuminates the interior space and provides easy wire replacement in low-light conditions.

Technical data

SVAROG 320 HD PULSE MODULE

MIG/MAG MMA method

Mains voltage V/Hz 3x400/50-60

Welding current range A/V MIG/MAG 30 - 320; MMA 20-300

Open circuit voltage U0 V 60

Network protection A 16 @

Max. effective current I1eff A 15.1

Welding current (DC=100%) I2 A 240 200

Welding current (DC=60%) I2 A 280 240

Welding current (DC=x%) I2 A 35%=320 30%=300

Insulation class IP 23S

Standards EN IEC 60974-1, EN 60974-10 cl. A

Dimensions mm 534 x 1141 x 943

Weight with cooling kg 84

Weight without cooling kg 77

The maximum load of the pull-out storage box is 25 kg

Weight without chassis kg 31.7

Wire speed m/min 1.0 - 20.0

Coil diameter mm 300 (15-18kg)

Coil weight kg max 18

Cooling capacity (Q=1l/min) kW 0.8

Total liquid content l 4.0

Max. pressure Bar 3.5

Max. flow l/min 8.0

*the device consists of modules. This kit includes a PL version with a platform module and a large chassis with one gas cylinder holder (ready to install the E.466 additional cooling module kit)

ALFAIN SVAROG-320-HD-PULSE-modular-prospekt-EN.pdf